Sea Side Aquatics
Simply The Best
Category Archives: Misc. News
- 10/2024
-
- 10/2024
-
NO WARRANTY OUTSIDE OF OUR NETWORK
Category : Misc. News
It has come to our attention that there are several counterfeit websites and fake products with Bubble-Magus logo being offered on various e-commerce platforms such as Amazon, Bubble-Magus.net, and other third-party sites. In light of this, SSA and Bubble Magus would like to officially announce that we will not provide any warranty for products purchased from these platforms, including Amazon, Ebay, Walmart, Chewy, Bubble-Magus.net, Alibaba, Aliexpress, Temu, or any direct purchases from other countries.
We want to particularly emphasize that the website Bubble-Magus.net is fraudulent, as it redirects users to Amazon. The provided address and phone numbers associated with this website are not genuine. Therefore, we strongly advise against purchasing any products from this site or any other suspicious platforms.
Please be cautious and ensure that you only purchase Bubble Magus products from authorized and trusted retailers. This will help guarantee the authenticity of the products and ensure that you receive the proper warranty support from SSA and Bubble Magus.
Thank you for your understanding and cooperation in this matter.
- 01/2024
-
- 02/2022
-
Bubble Magus New Roller Filters Version 2
Category : Bubble Magus , Misc. News , Other Filters / Reactors
ARF-S G2
Footprint: 4.52″ x 5.12″
Height: 15.35″
Width: 9.45″
Roll paper width: 3.93″
Use to Aquarium 300L
1″ PVC Pipe Connection
ARF-M G2
Footprint: 6.30″ x 6.50″
Height: 17.13″
Width: 11.42″
Roll paper width: 5.90″
Use to Aquarium 500L
1″ PVC Pipe Connection
ARF-L G2
Footprint: 8.66″ x 7.10″
Height: 17.13″
Width: 16.53″
Roll paper width: 7.87″
Use to Aquarium 1000L
1.25″ PVC Pipe Connection
- 12/2019
-
How to clean skimmer pump impeller
Category : Blog , Bubble Magus , JNS , Misc. News , Replacement Parts , Sea Side Aquatics , Your Choice Aquatics
This article will show you how to check and clean the skimmer pump impeller. Over period of time, depend on the amount of usage / calcium dosing. The ceramic shaft will bond / stuck into the impeller magnetic housing, this prevent the impeller from spinning correctly. If you hold the both end of the impeller with the thumb / index finger and try to spin the impeller, it should spin freely. If the impeller not spinning or you have to put lot of force into making it spin. The impeller / shaft needs cleaning.
The white shaft should easily be remove from the magnetic housing as well.
Picture 1 – Look at the red arrows, you will see evidence of build up.
Please watch the below YouTube videos to better understand
How to clean the impeller part 1
How to clean the impeller part 2
When the impeller is stuck into the magnetic housing, you can try to push the impeller out by putting one end on a hard flat object and push it. You might have to repeat the this steps a few times. Vinegar bath the whole impeller should also helped. Once you removed the shaft from the impeller, you can feel and see residue / calcium powder. You can use sand paper to sand it down or a brush to remove the residue. You want to clean off as much residue on the shaft and inside the magnetic housing as possible.
Once you done cleaning it, place the shaft back into the magnetic housing, you should feel there is no resistance and the shaft should be loose coming in and out of the impeller. Now try to hold both ends of the shaft and try to spin the magnetic impeller with your finger, the impeller should spin freely.
We suggest that you do this type of cleaning every 4-6 months, this would help extend the life of the impeller and the motor housing.
- 09/2019
-
How to replace the head cleaning screw
Category : Blog , Bubble Magus , How-To/Instruction , Misc. News , Other Filters / Reactors
Over period of time the wiper blade screw might became loose, please follow the steps to replace or tighten the screw for the cleaner head.
- 05/2019
-
- 02/2019
-
- 12/2018
-
Bubble Magus 2018 Rebate Free Coral Lens Kit
Category : Blog , Misc. News
For December of 2018, Sea Side Aquatics is offering FREE Bubble Magus coral lens kit to buyers with purchase of any listed qualified bubble magus items.
Please click on the flyer for more detail and print out the rebate form. Click here for the form bubblemagusrebate2018-2
- 11/2018
-
How to clean a dc pump impeller
Category : Blog , How-To/Instruction , Misc. News
There are so many dc pumps out there and all the impellers are pretty much the same or similar to each other. The most important part of keeping it clean and running without any issue is making sure the bearing is not stuck to the ceramic shaft and the calcium build up right behind the propeller.
Once you remove the impeller from the pump motor, please inspect the bearing inside the motor housing, make sure its there and if possible remove it. Place it to the impeller shaft, spin it or move it in and out making sure its loose. If its fit tight or you have to put some pressure or force into the movement. You need to clean the shaft and bearing. They should be loose and move freely.
Over time, the calcium also build up in the ceramic area right behind the propeller and in front of the magnet. right between the hole of the black plate.
Please follow the pictures instruction to identify the area and how to clean it.
