Author Archives: Sea Side Aquatics

New Fine Mesh Koi Nets

Tags :

Category : Blog , Misc , Your Choice Aquatics

Koi Fine Net

10 to 12″ Diameter

24″ long Handle

Aluminium Frame and Handle

White Fine Netting Material

Bubble Magus Small Roller Filter

The filter is a high-efficiency water filtration system which effectively removes suspended particles such as detritus, food, organic waste from the water column.

Use in marine aquariums, freshwater aquariums and corals system.

11.3″ long x 5.51″ wide by 15.4″ tall

Bubble Magus ARF-S Auto Roll Filter
ARF-S Specifications
• 12v DC motor
• 110v Power adapter ULc  DC12v 1amp output
• Water level switch
• Filter roll Non woven 102mm width, 25M length
• 1” I.D inlet pipe, complete with Flex pipe
• 287x140x390mm total dimensions (including motor body)
• Internal sump mounted
The ARF-S removes the need for filter socks. Water is fed into the internal chamber via the aquarium systems drain, and through the filter roll. When the water level rises in the chamber due to filter clogging the water level switch triggers the motor to wind on the filter roll to a new fresh piece. The water level will then drop repeating the process

Bubble Magus New Coral Lens Kit

Each box contains:

1 x precisely crafted lens holder clip
1 x polished 15k filter lens
1 x polished 20k filter lens
1 x professional grade 10x macro lens
1 x cleaning cloth

Capturing nature beauty in a perfect light, with the perfect angle using your smart phone or tablet have never been so easy with the new Bubble Magus Coral view lens.

Taking pictures of your beautiful corals often requires changing your aquarium light color spectrum or mount complex lighting setup. With the new Bubble Magus view lens, take pictures quickly and easily for the perfect shot every time.

Bubble Magus 2018 Rebate Free Coral Lens Kit

Category : Blog , Misc. News

For December of 2018, Sea Side Aquatics is offering FREE Bubble Magus coral lens kit to buyers with purchase of any listed qualified bubble magus items.

Please click on the flyer for more detail and print out the rebate form. Click here for the form bubblemagusrebate2018-2

How to clean a dc pump impeller

There are so many dc pumps out there and all the impellers are pretty much the same or similar to each other.  The most important part of keeping it clean and running without any issue is making sure the bearing is not stuck to the ceramic shaft and the calcium build up right behind the propeller.

Once you remove the impeller from the pump motor, please inspect the bearing inside the motor housing, make sure its there and if possible remove it.  Place it to the impeller shaft, spin it or move it in and out making sure its loose.  If its fit tight or you have to put some pressure or force into the movement. You need to clean the shaft and bearing. They should be loose and move freely.

Over time, the calcium also build up in the ceramic area right behind the propeller and in front of the magnet. right between the hole of the black plate.

Please follow the pictures instruction to identify the area and how to clean it.

How to change out control board for solar feeder

To change out the control board, please follow the below steps.

– 1 open the lid

– remove all 4 screws, at each corner of the feeder

– lay the unit on it side

– side the top portion out

– disconnect the 2 quick connections, please make note of which connector below to which one, this way no mistake when you plug them back.

– discounnect the connections at the control board

– remove 2 nuts from the controller board using plyer

– install the new board and connect everything back to where it belongs

– slide the top back and put the screws back

Please follow the below pictures

How to replace dosing head tube

Please carefully remove the dosing head by pressing down on both tabs on the side of the dosing head.

  • While pressing down the tabs, pull the head out.
  • One the dosing head is removed, please use a flat object to separate the front and the back plate of the head.
  • Place the back plate to a side and look at the position of the 3 rollers inside.  They need to be the same when finish otherwise it will not work correctly.
  • Carefully remove the rollers and the tubing along with the 2 clips
  • Once the rollers are removed, look into the dosing head, you will see a little groove, the rollers need to sit inside this groove evenly.  If one of the rollers are off set, it will not work.
  • Once the new tubing in place, snap the black plate back.
  • Once the head is back into the motor shaft, you can pull the tubing little to the left and little to the right.  This will freely place the rollers back to normal or smooth out the tubing as well.

Your Choice Aquatic Chillers

Model: C-018

Power: 1/8HP

Aquarium Volume: 80-400L

FLow Rate: 600-2000L/HR

Model: C-014

Power: 1/4HP

Aquarium Volume: 100-600L

FLow Rate: 1000-2500L/HR

Model: C-013

Power: 1/3HP

Aquarium Volume: 120-600L

FLow Rate: 1000-3000L/HR

Black Ceramic Frag Plugs

Category : Blog , Misc. News

Comes in Black Color