Category Archives: Bubble Magus


Bubble Magus New Roller Filters Version 2

ARF-S G2
Footprint:   4.52″  x 5.12″
Height:   15.35″
Width:    9.45″
Roll paper width:   3.93″
Use to Aquarium 300L
1″ PVC Pipe Connection
ARF-M G2
Footprint:   6.30″  x 6.50″
Height:   17.13″
Width:    11.42″
Roll paper width:   5.90″
Use to Aquarium 500L
1″ PVC Pipe Connection
ARF-L G2
Footprint:   8.66″  x 7.10″
Height:   17.13″
Width:    16.53″
Roll paper width:   7.87″
Use to Aquarium 1000L
1.25″ PVC Pipe Connection

Bubble Magus Mini Q Skimmer

Perfect skimmer for all in one tank !!

Coming Early 2022


Bubble Magus New Extreme Protein Skimmers

New Bubble Magus Extreme Protein Skimmers.

Comes with new improved SP Rock Pumps

CURVE 3 EXTREME

Measure:150*170*420

Use to 100-300L Aquarium

ROCK SP1.0 Pump

220-240V, 50Hz, 12W (120V, 60Hz, 0.5A)

Air intake: 270 LPH

CURVE 5 EXTREME

Measure:180*185*470

Use to 300-500L Aquarium

ROCK SP1.5 Pump

220-240V, 50Hz, 16W (120V, 60Hz, 0.5A)

Air intake: 330 LPH

CURVE 7 EXTREME

Measure:200*235*530

Use to 500-900L Aquarium

ROCK SP3.0 Pump

220-240V, 50Hz, 20W (120V, 60Hz, 1A)

Air intake: 660 LPH

CURVE 9 EXTREME

Measure:250*295*610

Use to 900-1500L Aquarium

ROCK SP4.0 Pump

220-240V, 50Hz, 25W (120V, 60Hz, 0.5A)

Air intake: 1000 LPH


4/15 Customer Testimonial On Skimmer Micro Bubbles

On 4/15 Customer contacted us:

Can not get micro bubbles to stop exiting from the bottom of skimmer. Its in 8 inches of water and has been running for 3 weeks. I had to block off the air to slow the over flowing down

 

 

 

 

 

 

 

Our replied to the customer and within 24 hours the customer replied

Running 10x better now!! I was going to return it because I’ve been playing with for 2 weeks now and couldn’t get it right. Thanks for your help!!


Bubble Magus D10-D11 DC Protein Skimmers

  D10

  DCS6000 Pump with Controller,  DC24V 45W

  Air intake: 1900L/H MAX.

  Use to 2000L Tank

  Footprint: 13.6” x 11.2”

  Height: 24.4”

  Water level suggested:  9.8”

  5.5” Dia. Collection neck

  D11

  DCS8000 Pump with Controller,  DC24V 68W

  Air intake: 2500L/H MAX.

  Use to 3000L Tank

  Footprint: 15.8” x 13.8”

  Height: 26”

  Water level suggested:  9.8”

  5.9” Dia. Collection neck

 


How to clean skimmer pump impeller

This article will show you how to check and clean the skimmer pump impeller. Over period of time, depend on the amount of usage / calcium dosing. The ceramic shaft will bond / stuck into the impeller magnetic housing, this prevent the impeller from spinning correctly. If you hold the both end of the impeller with the thumb / index finger and try to spin the impeller, it should spin freely. If the impeller not spinning or you have to put lot of force into making it spin.  The impeller / shaft needs cleaning.

The white shaft should easily be remove from the magnetic housing as well.

Picture 1 – Look at the red arrows, you will see evidence of build up.

Please watch the below YouTube videos to better understand

How to clean the impeller part 1

How to clean the impeller part 2

When the impeller is stuck into the magnetic housing, you can try to push the impeller out by putting one end on a hard flat object and push it.  You might have to repeat the this steps a few times. Vinegar bath the whole impeller should also helped. Once you removed the shaft from the impeller, you can feel and see residue / calcium powder.  You can use sand paper to sand it down or a brush to remove the residue. You want to clean off as much residue on the shaft and inside the magnetic housing as possible.

Once you done cleaning it, place the shaft back into the magnetic housing, you should feel there is no resistance and the shaft should be loose coming in and out of the impeller.  Now try to hold both ends of the shaft and try to spin the magnetic impeller with your finger, the impeller should spin freely.

We suggest that you do this type of cleaning every 4-6 months, this would help extend the life of the impeller and the motor housing.


How to replace the head cleaning screw

Over period of time the wiper blade screw might became loose, please follow the steps to replace or tighten the screw for the cleaner head.

 


Bubble Magus Commercial Skimmers

SK-1:   

Measure:400*600*1520mm (15.8″ x 23.6″ x 60″)

Foot Print: 15.8″ x 23.6″

Cylinder Dia.:9.8″

Capacity:5-10 Ton

Pump:BUBBLE-MAGUS WP10000, 220~240V, 50Hz, 105W, Hmax 5M, Qmax 1000L/H.

SK-2:  

Measure:650*700*2100mm (25.6″ x 27.6″ x 82.7″)

Foot Print: 25.6″ x 27.6″

Cylinder Dia.:11.8″

Capacity:20-30 Ton

Pump:TDA50, 220~240V, 50Hz, 370W, Hmax 10M, Qmax 180L/min.

 


Bubble Magus Roller Filters

We have in stock the Small and Medium version, Large version is coming soon.